Gas generator sets in low temperature conditions, fuel viscosity increases and is not conducive to gas combustion, then gas generator sets in low temperature state which start mode, today Jinan jichai Huanneng small series for you to briefly introduce the gas generator set low temperature start mode.

1、選用低溫性能好的瓦斯好色先生在线观看,低溫黏度小，各摩擦副間潤滑好，啟動阻力小，利於啟動。目前使用的多級油，如15W/40W前的數字越小則機油的低溫流動性越好。因此，低溫時推薦使用10W或5W機油。

1. The gas generator set with good low-temperature performance has small low-temperature viscosity, good lubrication between friction pairs and small starting resistance, which is conducive to starting. For the multi-stage oil currently used, the smaller the number before 15W / 40W, the better the low-temperature fluidity of the oil. Therefore, it is recommended to use 10W or 5W oil at low temperature.

2、采用低溫性能好的蓄電池必要時可對蓄電池進行保溫，以保證其低溫條件下能正常充電且有足夠的輸出電流，從而提高了啟動係統功率。

2. The battery with good low-temperature performance can be used to keep the battery warm when necessary, so as to ensure that it can be charged normally under low-temperature conditions and has enough output current, so as to improve the power of the starting system.

瓦斯好色先生在线观看有哪些常見的低溫啟動方式

What are the common low-temperature start-up modes of gas generator set

瓦斯好色先生在线观看有哪些常見的低溫啟動方式

What are the common low-temperature start-up modes of gas generator set

3、加注冷起動液。

3. Fill in cold starting fluid.

4、火焰預熱啟動。

4. Flame preheating starts.

5、循環水加熱係統(也稱燃油加熱器加熱係統)。

5. Circulating water heating system (also known as fuel heater heating system).

6、其他的預熱方式除上述預熱方式外，還可采用熱水預熱法、蒸氣預熱法、電預熱法等多種方法進行低溫啟動。

6. In addition to the above preheating methods, other preheating methods can also use hot water preheating method, steam preheating method, electric preheating method and other methods to start at low temperature.

操作時，必須保證箱式變電站低壓進線開關處於斷開位置，機組油、水、合上預供油開關，啟動電動預供油泵(或扳動手搖機油泵)。待主油道壓力達100kPa啟動要求值後，按下起動按鈕“Start”，機組起動後，可按下“翻頁"按鈕，通過液晶顯示屏檢查發動機運行中各項技術參數的變化。

During operation, it must be ensured that the low-voltage incoming line switch of the box type substation is in the off position, the oil and water supply switch of the unit is closed, and the electric pre supply oil pump (or the hand oil pump) is started. After the main oil passage pressure reaches the required value of 100KPA, press the start button "start". After the unit is started, press the "turn page" button to check the changes of various technical parameters during the engine operation through the LCD.

起動成功後應怠速暖機，當機油溫、水溫達到40℃以上，方可加速、加載。按動或調節控製屏上加減速旋鈕調整機組的頻率，使之略高於額定頻率。調整控製屏上的電壓調節器的微調旋鈕，使交流電壓表在400V位置，按下“I/O”按鈕，此時在站控室SCADA監控界麵上“發電機”欄中可監控相關數據，機組便向負載供電。

After starting successfully, the engine should be warmed up at idle speed. When the oil temperature and water temperature reach above 40 ℃, the engine can be accelerated and loaded. Press or adjust the acceleration and deceleration knob on the control panel to adjust the frequency of the unit to slightly higher than the rated frequency. Adjust the fine-tuning knob of the voltage regulator on the control panel to make the AC voltmeter at 400V position, press the "I / O" button, then the relevant data can be monitored in the "generator" column on the SCADA monitoring interface of the station control room, and the unit will supply power to the load.